CARBON FIBER HOOD 2015 WRX INSTALL
The DIY install will leave you proud of the work you've done. Over time the bond becomes stronger and the water you used will evaporate completely. Should anything come up in the few hours after install, just use heat immediately to press it down. Do not use a squeegee or anything else that could potentially scratch the material. Center the overlay up on the hood scoop and start pushing out all the water / soap with your fingers. Start at the very back of the hood scoop. If it would burn you, it will probably burn the material. Just make sure you use small amounts of heat and work you way up. Using heat from a hair dryer or heat gun will be essential. Our pre-mixed StickerFab Fluid works THE BEST. This will allow you to slide the vinyl around, but will require the use of heat to really make it stick. All VIS Carbon Fiber Hoods and Trunks are manufactured using a two-part construction design. Hoods and Trunks are made from 100 ISO-certified, Grade-A carbon fiber material. The easiest way to apply this is to wet the back of the vinyl. Carbon Fiber Hood VS 2 Style for Subaru WRX 4DR 2015-2021. INSTALLATIONĬlean the surface of the hood. Semi Gloss Black is US sourced Avery brand and Matte Black is from Orafol which is a German company. Rated EXCELLENT for WATER RESISTANCE, HUMIDITY RESISTANCE, and SOLVENT RESISTANCE. Minimum application temperature is 40 degrees Fahrenheit. The air egress liner also aids in large graphic application. This repositionable permanent adhesive offers minimal initial bond growing to permanent bonds that facilitates application of large graphics. This film has excellent dimensional stability, outstanding durability and outdoor performance. Dragon Wrap™ Carbon Fiber Films (3D Carbon) is a 5.6 mil calendered vinyl film featuring a clear repositionable permanent acrylic adhesive on an air-egress liner. I use premium vinyl which has high initial costs, but are the industry standards for high quality materials. When purchasing vinyl overlays, keep in mind that not all materials are created equally. NOT ALL MATERIALS ARE CREATED EQUALLYĬUSTOMER MESSAGE - "Got them just now, thanks for including a(n) extra set! I've had 2 sets of CF look ones from another seller and silver stars kept peeling and the carbon look faded really bad." Please visit my store if you are looking for other 2015+ WRX / STI products or products for a different model. Material standards are high.įor the 3D Carbon material, do not apply wax. I source the vinyl for these products from US suppliers. This material is durable and will last for years. For one, it is easier to install that way and two, it ultimately will look better this way. It maintains even spacing and the reason for this will be clear during installation. It runs parallel to the front of the hood scoop. A little vinyl in the right places can really make your vehicle stick out compared to any stock vehicle! Please note the design of this overlay. Working with overseas suppliers we have stumbled upon a lot of interesting products. We actually got the design inspiration from a Japanese hood scoop overlay. These products are intended for off-road use only, unless your local and state laws state otherwise.3D Carbon Hood Scoop Overlay - 2015-2021 WRX / STI Due to the unknown nature of the intended uses of these products, hood pins are required. Please be sure to look for the badge when purchasing.
CARBON FIBER HOOD 2015 WRX FULL
We are transitioning our full spectrum of carbon parts to use the VIP process so that our customers can enjoy these improved products without incurring a huge cost increase.Īll VIS Carbon Fiber Hoods and Trunks come with a VIS badge of authenticity. In 2014, we further improved on this manufacturing process by introducing the Vacuum Infusion Process (V.I.P.), which utilizes a single-mold vacuum to produce parts that are 10-20% lighter than before while improving durability.
The edges are smoothed by hands to insure good quality finish all around. A one-piece, smooth underside shell is fused to the top layer enhancing the product’s structural integrity. The top layer is composed of carbon fiber material bonded to the hood surface with high-grade epoxy resin, and finished with an ultra-clear (Poly Shield), UV-protective polyurethane coating for a high gloss finish.
Hoods and Trunks are made from 100% ISO-certified, Grade-A carbon fiber material. Carbon Fiber Trunk SS Style for Subaru WRX 4DR 2015-2021
0 kommentar(er)
